Increase vTaskdelay in main loop

platformio.ini

@@ -13,7 +13,7 @@ data_dir = data/build
 
 [env]
 platform = espressif32
-framework = arduino
+framework = arduino, espidf
 monitor_speed = 115200
 upload_speed = 921600
 monitor_filters = esp32_exception_decoder, colorize
@@ -22,7 +22,7 @@ build_flags = !python scripts/git_rev.py
 
 [esp32wemos-s3-mini_BW_base]
 platform = espressif32
-framework = arduino
+framework = arduino, espidf
 board = lolin_s3_mini
 board_build.partitions = partition.csv
 lib_deps = 
@@ -37,7 +37,7 @@ build_flags =
   -DLAST_BUILD_TIME=$UNIX_TIME
   -D IS_S3
   -D IS_BW
-#  -D CONFIG_FREERTOS_USE_TRACE_FACILITY
+  -D CONFIG_FREERTOS_USE_TRACE_FACILITY
   -D WITH_RGB_LED
   -D NEOPIXEL_COUNT=4
   -DASYNCWEBSERVER_REGEX
@@ -47,7 +47,9 @@ build_flags =
   -mfix-esp32-psram-cache-issue
   -fexceptions
   -DPIO_FRAMEWORK_ARDUINO_ENABLE_EXCEPTIONS
-build_unflags = -fno-exceptions
+build_unflags = 
+  -fno-exceptions
+  -Werror=all
 
   zinggjm/GxEPD2@^1.5.2
 

sdkconfig.defaults

@@ -0,0 +1,21 @@
+CONFIG_AUTOSTART_ARDUINO=y
+# CONFIG_WS2812_LED_ENABLE is not set
+CONFIG_FREERTOS_HZ=1000
+CONFIG_FREERTOS_USE_TRACE_FACILITY=y
+CONFIG_FREERTOS_USE_STATS_FORMATTING_FUNCTIONS=y
+CONFIG_FREERTOS_GENERATE_RUN_TIME_STATS=y
+
+CONFIG_MBEDTLS_PSK_MODES=y
+CONFIG_MBEDTLS_KEY_EXCHANGE_PSK=y
+
+CONFIG_BOOTLOADER_LOG_LEVEL=0
+CONFIG_LOG_BOOTLOADER_LEVEL_NONE=y
+CONFIG_BOOTLOADER_LOG_LEVEL_NONE=y
+CONFIG_ESP32S3_SPIRAM_SUPPORT=y
+CONFIG_LOG_DEFAULT_LEVEL_NONE=y
+CONFIG_LOG_DEFAULT_LEVEL=0
+CONFIG_LOG_MAXIMUM_LEVEL=0
+CONFIG_LOG_BOOTLOADER_LEVEL_NONE=y
+CONFIG_LOG_BOOTLOADER_LEVEL=0
+
+CONFIG_HEAP_CORRUPTION_DETECTION=CONFIG_HEAP_POISONING_LIGHT

src/lib/functions.cpp

@@ -60,8 +60,25 @@ void setupComponents()
     pixels.show();
 #endif
 
-    // delay(3000);
-    // Serial.println(F("Leds should be on"));
+//     delay(6000);
+//     Serial.println(F("I2C Master"));
+
+// int i2c_master_port = 0;
+// i2c_config_t conf = {
+//     .mode = I2C_MODE_MASTER,
+//     .sda_io_num = 35,         // select SDA GPIO specific to your project
+//     .scl_io_num = 36,         // select SCL GPIO specific to your project
+//     .sda_pullup_en = GPIO_PULLUP_ENABLE,
+//     .scl_pullup_en = GPIO_PULLUP_ENABLE,
+//     .master = {
+//         .clk_speed = 400000,  
+//     }, // select frequency specific to your project
+//     .clk_flags = 0,                          // optional; you can use I2C_SCLK_SRC_FLAG_* flags to choose i2c source clock here
+// };
+
+// i2c_param_config(i2c_master_port, &conf);
+// ESP_ERROR_CHECK(i2c_driver_install(i2c_master_port, conf.mode, 0, 0, 0));
+Wire.begin(35, 36); 
 
 #ifndef NO_MCP
     if (!mcp.begin_I2C(0x20))
@@ -72,8 +89,8 @@ void setupComponents()
         pixels.setPixelColor(2, pixels.Color(255, 0, 0));
         pixels.setPixelColor(3, pixels.Color(255, 0, 0));
         pixels.show();
-        while (1)
-            ;
+        // while (1)
+        //     ;
     }
     else
     {
@@ -222,8 +239,8 @@ void handleScreenTasks(uint screen)
         vTaskSuspend(blockNotifyTaskHandle);
     if (getPriceTaskHandle)
         vTaskSuspend(getPriceTaskHandle);
-    if (minuteTaskHandle)
-        vTaskSuspend(minuteTaskHandle);
+    // if (minuteTaskHandle)
+    //     vTaskSuspend(minuteTaskHandle);
     switch (currentScreen)
     {
     case SCREEN_BLOCK_HEIGHT:
@@ -376,18 +393,23 @@ void showNetworkSettings()
     String ipAddr = WiFi.localIP().toString();
     String subNet = WiFi.subnetMask().toString();
 
-    epdContent[1] = "IP/Subnet";
+    epdContent[0] = "IP/Subnet";
 
     int ipAddrPos = 0;
     int subnetPos = 0;
     for (int i = 0; i < 4; i++)
     {
-        epdContent[2 + i] = ipAddr.substring(0, ipAddr.indexOf('.')) + "/" + subNet.substring(0, subNet.indexOf('.'));
+        epdContent[1 + i] = ipAddr.substring(0, ipAddr.indexOf('.')) + "/" + subNet.substring(0, subNet.indexOf('.'));
         ipAddrPos = ipAddr.indexOf('.') + 1;
         subnetPos = subNet.indexOf('.') + 1;
         ipAddr = ipAddr.substring(ipAddrPos);
         subNet = subNet.substring(subnetPos);
     }
+    epdContent[NUM_SCREENS-2] = "RAM/Status";
+
+  //  char buf[32];
+//    snprintf(buf, sizeof(buf), "%s/%s", round(ESP.getFreeHeap()/1000), );
+    epdContent[NUM_SCREENS-1] = String((int)round(ESP.getFreeHeap()/1000)) + "/" + (int)round(ESP.getHeapSize()/1000);
 
     CustomTextScreen::setText(epdContent);
 

src/main.cpp

@@ -87,4 +87,5 @@ void setup()
 
 void loop()
 {
+  vTaskDelay(pdMS_TO_TICKS(5000));
 }